Results 1 to 5 of 5
  • Topic Tools
  • Display
  • Bookmark and Share
  1. #1
    New Member
    Points: 57, Level: 1
    Level completed: 7%, Points required for next Level: 93
    Overall activity: 99.0%
    Achievements:
    New Achievement!

    Join Date
    Jan 2013
    Location
    Austria
    Posts
    3
    Points
    57
    Level
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0

    HTS3367 Firmware upgrade did not work

    Hello to the forum !

    Yesterday i tried to upgrade my HTS3367/12, because we often had troubles with new DVDs ( original ones - "no disk" ). So i thought it would be a good idea to check the firmware - 00.27.??

    After copying the 00.35.00 to an USB stick i follwed the installprocedure. The display showed WRITE und counted down several times. I think it was the third time, when it got stuck on WRITE01, so i waited for about an hour - then i turned the system on/off. Since then nothing else, than a running fan and one short flashing of the powerled after connecting to the power, happens.

    Could somebody help me "reloading" the system, or is it gone forever ?

    Thanks in advance

    Joe

  2. #2
    New Member
    Points: 113, Level: 1
    Level completed: 63%, Points required for next Level: 37
    Overall activity: 0%
    Achievements:
    New Achievement!7 days registered100 Experience Points

    Join Date
    Jan 2013
    Location
    The Netherlands
    Posts
    6
    Points
    113
    Level
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Can you still turn on the device and enter the menu? Check if you can see if the firmware is upgraded. If not:

    - Format the USB device you use for upgrading the firmware;
    - Make sure you only copy the firmware files to the usb stick;
    - Try to update again using the philips install procedure.

    If this doesn't work you might try a different USB stick and follow the above instructions. Maybe this works?

  3. #3
    New Member
    Points: 57, Level: 1
    Level completed: 7%, Points required for next Level: 93
    Overall activity: 99.0%
    Achievements:
    New Achievement!

    Join Date
    Jan 2013
    Location
    Austria
    Posts
    3
    Points
    57
    Level
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    As i mentioned above, the device does not start any longer. After powering up, the fan on the backside starts and for a very short time the power-led is lighting up once - nothing else.

    I already tried using a USB-stick at startup-time,like booting from USB device, but this although doesn't work.

    Any other ideas ? Is there some kind of press-button-combination to start from USB ?

  4. #4
    Platinum Member
    Points: 2,996, Level: 15
    Level completed: 82%, Points required for next Level: 54
    Overall activity: 0%
    Achievements:
    1 year registered1000 Experience PointsOverdriveNew Achievement!
    Awards:
    Discussion Ender
    Oscar's Avatar
    Join Date
    Feb 2011
    Posts
    722
    Points
    2,996
    Level
    15
    Thanks
    1
    Thanked 5 Times in 5 Posts
    Rep Power
    4
    Hi Joe,

    Maybe best to first try and start it up again ( if possible ). Take out the USB first and try some things. Did you unplug already for some minutes and plugged it back in? If so and not working try to unplug, press the power button and keep it pressed for some time while putting back the mains.....

    Let me know and good luck

  5. #5
    New Member
    Points: 57, Level: 1
    Level completed: 7%, Points required for next Level: 93
    Overall activity: 99.0%
    Achievements:
    New Achievement!

    Join Date
    Jan 2013
    Location
    Austria
    Posts
    3
    Points
    57
    Level
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Rep Power
    0
    Its up and running again !

    Unfortunately normal procedures didn't help - as a last chance and to avoid electronic garbage i tried the technical way ( at one's own risk ).

    With the help of the www we could find a good instruction: How to recover a dead player using a serial cable.
    After soldering the electronic-parts for connecting the hts3367 to a pc via rs232, i could upload the 00.35.00 HTS336x.bin image.
    Then following the normal USB upgrade-procedure - this time with a new fat32 formatted stick and only HTS-SW on it ;-) - everything is fine.

    Even my problem with reading the new DVDs is gone !

    Joe

Similar Topics

  1. HTS 3541/51 firmware V1.52.00 update does not work
    By arif77 in forum Sound: Immersive Sound (5.1 system)
    Replies: 0
    Last Post: 10-25-2012, 08:51 AM
  2. Replies: 3
    Last Post: 06-06-2012, 07:42 AM
  3. DCM580 - Doesn't work after upgrade to version 45
    By Dr.Soidberg in forum Sound: Other Apple Docking Solutions
    Replies: 12
    Last Post: 04-16-2012, 10:20 AM
  4. Don't work with new firmware
    By CarecaIII in forum Apps: MyRemote App (for Android)
    Replies: 3
    Last Post: 10-19-2011, 02:15 PM
  5. Upgrade to software version 140.40 does not work
    By conte in forum TV: Software 2010 models
    Replies: 8
    Last Post: 08-27-2011, 04:36 PM

Tags for this Topic

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •