Experience thread - FW v150.85 - for 6/7/8/9xx7 Series - 2012

[majorusa]

For the first time last nigh the update procedure failed. I received a message on the screen saying that the update cannot complete and I was advised to take out the USB, turn off the TV then turn on and follow the instructions on the screen. I did this then it was "no software present". I reinserted the USB flash drive and the Update restarted and completed. It was an adrenaline ride!

On the update procedure:
1. Turn on the TV set
2. Insert the USB flash drive with the autorun.upg file in it
3. The TV will detect the upgrade automatically if the autorun.upg version is newer that the sw version on the TV and will start the upgrade process
4. Wait till a message stating that the upgrade is complete, remove all inserted USB devices and pull the power cord for one minute.
5. Remove all USB devices and pull the cord.
6. Wait 2 minutes to be sure that all processes ended
7. Plug in the cord.
8. Enjoy / get frustrated by your TV!

There you go. I performed this procedure for each upgrade since the initial fw the TV was first shipped.

[L1Zeeman]

Never ask me for remove the power cord ... only for remove pendrive.
Philips never gave one instructions what to do after FW update - where can you read (manual, www Philips, forum), there are written differently.

The textbox I get on my 32PFL6007H/12 says: "Remove all inserted USB memory devices. Disconnect the mains power cable. Reconnect after one minut."
Maybe the text is different in other languages (I use English)? Or could it be related to the version of the electronic user manual on the TV?

[niki999]

The textbox I get on my 32PFL6007H/12 says: "Remove all inserted USB memory devices. Disconnect the mains power cable. Reconnect after one minut."
Maybe the text is different in other languages (I use English)? Or could it be related to the version of the electronic user manual on the TV?

Nope it is the right text i get the same text. I do that every time I install a new firmware and never had any problems.

[kookaburra]

Hi,

The new FW is now live.

For detailed technical feedback, please use this thread.

Edit: For technical feedback please post in the following thread.
This thread should be for more details and discussions.


IMPORTANT: After upgrading your TV, it is necessary to perform a "cold start". This means that, after the TV is running again (after the update), shut down the TV, wait 1 minute (till all components are shut down), and unplug the TV from the mains (pull power cord) for 2 minutes before starting again.

Changelog:

QF1EU-0.150.85.0

- not available yet

Toengel@Alex

Local Dimming pumps, PNM artifacts ... All these problems are the same as we have in our moelos 2011 (21:9). Does this mean that we will soon have an update for these problems in our teleisores 2011.

Best Regards

Google translator.

[Joachim]

The bug TVs switches from Standby to a mode 'like "Quick Start"', even though the "Quick Start", "Activate" is "Off" still remains in 150.085 .

[x7007]

Anything new with the philips 7007 Pixel underscan to the right and the buttom on tests it doesn't show the white line which it should On the buttom and right side, it just takes it too much to the right and down, left and up are Ok.

[mrb1972]

Here is the change log so far taken from the german philips support website

Changelog:

# No SmartTV access in conjunction with various routers / solved
# No SmartTV access / Philips server not found / solved
# Intermittent flickering backlight in high-contrast scenes change, if only dynamic backlight is activated / released
# 60PFL9607S/12 - 3D Max Clarity and 2 player gaming mode solved /
# PNM performance optimizations
# PQ improvements (in terms of shocks, halos, artifacts, etc.)
# Pops when switching HDMI sources external dissolved

[emer]

Never ask me for remove the power cord ... only for remove pendrive.
( ... )

Sorry ...
"plug out any USB, plug out cord, 1 minut, plugin in" - that's the info after update ...

[vulliw]

Sorry ...
"plug out any USB, plug out cord, 1 minut, plugin in" - that's the info after update ...

that's right here in holland exactly the same

[x7007]

philips, what about this problem ? it is really annoying as it's not 1:1 pixel mapping, and some thing are out of the screen, harder to click and harder to see/read

http://www.supportforum.philips.com/...ll=1#post50095

Picture Shift ( Doesn't Work AT ALL)
I' go in the setup go to Picture Shift, it doesn't move anything in OFF , game or computer mode. using PC > HDMI > TV Radeon 7970.

Can u replicate this problem and fix this ? The only screen i think it maybe did anything is in the Firmware update screen which look offscreen but i can't move anything there while it's there. When u in Picture shift and i am just clicking one side, lets say Left, the Left arrow in the picture shift will dissapear after couple of clicks which means it works but nothing change on the screen. I tried Unscaled or Wide screen, still nothing seem to work.

[x7007]

Why is this happening !!

http://www.youtube.com/watch?v=U2j2v...ature=youtu.be

http://www.supportforum.philips.com/...e-the-2nd-time

[Philips - Benedickte]

Why is this happening !!

http://www.youtube.com/watch?v=U2j2v...ature=youtu.be

http://www.supportforum.philips.com/...e-the-2nd-time

Hi x7007.

Could you please confirm that the software is updated and you have unplugged the TV for 2 mins?
What is the result after this?

Best regards,
Benedickte

[x7007]

Yes the firmware was upgraded all the times 1.50.85 currently the last time i updated. and I followed the unplugged rule all the time from the start.

I can replicate it everytime.
Watch this
http://www.youtube.com/watch?v=ZqD96...ature=youtu.be

as follows
Software update QF1EU-0.150.85.0
Current Software : QF1EU-0.150.85.0
Release notes: Release for FusionR2:
QF1EU-0.150.85.0_bld11a
Generation date:
24/02/2013 23:23:54

Everytime i change Source there is Green-Pinky flash from the TV almost the same as i get from the Firmware update ?

Does everyone has it when they change source ?
No matter if the source is connected or on.

I found the problem, everytime i go in the USB menu from Source i get the Scrambled screen ! and if i click to change source again the all screen is scrambled until i change Source.

1.When going to USB from source menu and going to Satalite which i don't have anything connected to it get the green pink screen,
2.When going to USB from source menu and going to TV which i don't have connected i get black screen, if i click Source again i get the scramble screen pink-green.
3.When going to USB from source menu and going to Computer everything is ok, Computer mode always fix it if there are the pink-green scramble.
4.When going to USB from source menu and going to Game-Mode which is PS3 which not turned on i get black Screen and little fast scramble for a sec and going to Satalite or TV doesn't have scramble.
5.When going to USB from source menu and going to HDMI4-5 YCbcR VGA and going to Satalite or TV doesn't show scramble anymore

What is wrong with the USB Tv screen ? and why HDMI Computer input fixes it ?

It doesn't look like TV problem, but more firmware thing, cause i can replicate it, still i didn't check this thing before but i remember i had those little scrambles when i first turned on the tv when moving and making sources the first time, so i can't be sure.
TV came with 1.33.5

I will get it on film, please fix this.

[x7007]

Philips, do u have any idea what is going on ?

NO One else can replicate it ?

[Syncmahv]

philips, what about this problem ? it is really annoying as it's not 1:1 pixel mapping, and some thing are out of the screen, harder to click and harder to see/read

http://www.supportforum.philips.com/...ll=1#post50095

Picture Shift ( Doesn't Work AT ALL)
I' go in the setup go to Picture Shift, it doesn't move anything in OFF , game or computer mode. using PC > HDMI > TV Radeon 7970.

Can u replicate this problem and fix this ? The only screen i think it maybe did anything is in the Firmware update screen which look offscreen but i can't move anything there while it's there. When u in Picture shift and i am just clicking one side, lets say Left, the Left arrow in the picture shift will dissapear after couple of clicks which means it works but nothing change on the screen. I tried Unscaled or Wide screen, still nothing seem to work.

Same here.
Still get the same problem, no 1:1 pixel mapping in game/computer mode !