Your experiences with FW v0.140.40.0 for 5xx5, 6xx5, and 7xx5 series (2010 models)

[beenstra2006]

New software 140.40 solved the problem (connection failure to the server). NetTV works fine again. Thank you Philips. Good work.

[banjeep]

New software 140.40 solved the problem (connection failure to the server). NetTV works fine again. Thank you Philips. Good work.

I not solved the problem connection nettv

[Toengel]

Hi,

try to clear your Net TV memory and shut down the TV completely (hard off) for 2-3 minutes...

And please re-check your settings for LAN/WLAN

Toengel@Alex

[Chrissie18]

And don't forget to wait 1 or 2 minutes after turning on the TV before swithing to NetTV.
IT is still initializing during that period...

[skizo]

Hello,

I have a strange problem with my PFL7655H with firmware 000.140.040.000.

My PS3 is connected to the AV receiver (Yamaha RX-V667) wich is connected to my television, both by HDMI. I can hear the sound of the PS3 perfectly on the TV with the receiver off. If I turn the receiver on, the TV silences its own speakers since it has Easylink enabled and I can hear the sound perfectly from the receiver speakers. So far so good..

Unfortunatly, when I turn the receiver off, the tv enables its own speakers but there's no sound or the sound is very low and completly distorted. The only way things get back to normal is turning the TV OFF and ON again.

I've noticed this same behaviour with another console (Xbox 360) and with my IPTV provider box, also attached to the AV receiver by HDMI.
Since the problem is fixed turning the TV OFF and ON again, I suspect the problem is on the PHILIPS side..

Anyone with a similar problem?
Local PHILIPS support doesn't have a clue..

Kind regards,
Rui

edit: another post/same problem
http://www.supportforum.philips.com/...DMI-interfaces

[Niels]

I have been using 140.040 now for two days and I can confirm that the IP EPG speed has increased significantly to acceptable levels !

Unfortunately today the IP-EPG did not show up after selecting it and also Net TV was very slow.
I decided to clean the NET-TV memory, but that made everything even worse. Now I have no EPG and no NET-TV. When I select it, it displays the general conditions, when I select to continue, the conditions keep scrolling on the screen for minutes and after that: ... NOTHING !
Restarting the TV and shutting it down for minutes did not make a difference. Please HELP !

[shankly1985]

Sorry to tell you this but where all having theses sound drop outs, PHILIPS sucks big time. Had this TV over 7 months and there still trying to fix this with updates. this will be last philips product I ever buy.

Hello,

I have a strange problem with my PFL7655H with firmware 000.140.040.000.

My PS3 is connected to the AV receiver (Yamaha RX-V667) wich is connected to my television, both by HDMI. I can hear the sound of the PS3 perfectly on the TV with the receiver off. If I turn the receiver on, the TV silences its own speakers since it has Easylink enabled and I can hear the sound perfectly from the receiver speakers. So far so good..

Unfortunatly, when I turn the receiver off, the tv enables its own speakers but there's no sound or the sound is very low and completly distorted. The only way things get back to normal is turning the TV OFF and ON again.

I've noticed this same behaviour with another console (Xbox 360) and with my IPTV provider box, also attached to the AV receiver by HDMI.
Since the problem is fixed turning the TV OFF and ON again, I suspect the problem is on the PHILIPS side..

Anyone with a similar problem?
Local PHILIPS support doesn't have a clue..

Kind regards,
Rui

edit: another post/same problem
http://www.supportforum.philips.com/...DMI-interfaces

[gledalec]

Hello,
new software 140.40 solved the problem on my PFL7605H/12 (connection failure to the server). NetTV works fine again. Thank you Philips.

Well done.

[eringard]

40PFL5605 always the same sound off problem when switching HDMI

[Niels]

Hello,

Just wanted to update you all on my problem I described below.
After contact with the servicedesk Philips decided to send someone to me to fix the problem.
Although it looked like a SW problem (there was contact with the Philips server, but the TV did not continue to the 'registration' page or NetTV page), it was solved by replacing the main board.

I used the TV now for only one day after the replacement, but I noticed already 3 times that the TV did something like an 'automatic reset' (screen went black for 1 second). After this reset it also takes again about 2 minutes before I can use Net-TV or the IP-EPG.
I called Philips again, since I do not trust this situation. I will keep you updated.

Kind regards,
Niels

Unfortunately today the IP-EPG did not show up after selecting it and also Net TV was very slow.
I decided to clean the NET-TV memory, but that made everything even worse. Now I have no EPG and no NET-TV. When I select it, it displays the general conditions, when I select to continue, the conditions keep scrolling on the screen for minutes and after that: ... NOTHING !
Restarting the TV and shutting it down for minutes did not make a difference. Please HELP !

[BaYRoLeX]

This version still didn't solve the audio drop problem through HDMI on my 42PFL7695H/12

[Aleks]

Hi.Whether will be new FW for TVs of 5-7 versions 2010? Or we are forgotten?

[Toengel]

Hi,

firmware 140.40 was already released for 5000 (Net TV models) to 7000 models...


Toengel@Alex

[Aleks]

For the TV version 5-6 in 2010 (without NET TV) latest FW 000.140.039 (27.07.2011.)Uzhe of 2 months there is no support!!!

[Toengel]

Hi,

version 140.40 only fixes a Net TV problem... so, also nothing new with the other 2010 TVs...

Toengel@Alex