Problems with the network cable
Since I installed the latest firmware on my TV 000,140,025,000 37PFL7605H/12 sometimes loses the IP address. The TV is connected to the router via Ethernet. To resume the IP address must unplug the network cable and reinsert it. How can I fix it? I checked the router, the cable network and so on. but it seems that the problem with the TV. Before the latest firmware has never occurred.
It may be a bug. But you can try to lower DHCP lease time setting in your router. Set it to two minutes, for example. Maybe this can help... But this is not normal solution, ask Philips about it.
Why don't you use a static IP? I am using a static IP on mine, and has never disconnected.
I installed the new firmware 140.027 but the problem seems not solved the ethernet connection. The problem occurs randomly. I checked both the router and network point but it's all right. What else can I check?
I've the same problems with the ethernet connection.
In my case, the dlan access point (devolo) crashes when the wire is connected to the TV and I turn on the TV (cold start; not from stand-by mode). I have to repower my access point (without any wired connection) to get it back to work.
If I turn on the TV (cold start) and connect the wire after the Home-Screen is loaded, I have to reconfigure the lan settings. After that -> NetTV works fine (don't know how long it works?!).
For me is this no solution to use NetTV. The effort is definitely to high.
Has someone an idea how to solve that problem?
Excuse have you upgraded the firmware to 140.025? On my TV since I did this update has the problem occurred. But the Italian philips support keeps telling me that this is the router or ISP problem.
This is definitly no problem focused by the Router or the ISP! I've tested other hardware (non-Philips-stuff) connected via the same wire on the same port and there is no problem with the connection.
After setting up the TV (2011-01-19) and connecting it with my AP there appeard a messagebox with a notification of a new firmware. I confirmed the messagebox and the new firmware was installed:
After rebooting the TV with the new firmware -> the trouble with NetTV began.
Please try again with connecting the TV directly to the router. Also switch "off" the firewall.
If still no success, please report your Ethernet MAC address to firstname.lastname@example.org.
To find your MAC address, put the TV on a normal TV channel and press "123654" on the remote control. Now you see CSM1. Press down, down, until you see CSM3. Here the Ethernet MAC address is mentioned. With this MAC address we can check your data and fix the problem.
Last edited by Philips; 01-27-2011 at 10:14 AM.
Hi fm5000, sent you email to Net TV Support? Have you received any response? I have contacted the support Italian but I haven't solved the problem. They sent me the link to this post for info. Best regards
I've written an email that contained the mac-address of the ethernet contoller and they answered quickly to my email.
They wrote that they will perform a device reset via the portal-side. I've also still reconfigured my network infrastructure. I've added a switch to the access-point and the TV is now connected via the switch to the www. After two days of testing I can say: it works; unfortunately, sometimes it is a bit slow.
btw @ philips team: thank you for the fast support.
Last edited by Philips; 01-31-2011 at 01:06 PM.
Reason: removed link, had no added value.
Originally Posted by Philips
What does this means?
Originally Posted by fm5000
How they can reset remote device and fix any problems with only knowledge of Ethernet MAC-address?
Does Philips sends MAC-addresses inside of IP-packets?
If so then this is not good news...
Have You just sent an email with the MAC or even a description of the problem? Since I am not good at English so I was wondering if you just need the MAC
I think they recognize each device in there servers and maybe they have a database entry for each device (MAC) with additional infos such as tv model etc. I think with "reset via protal-side" they mean resetting their database entry...
But this is speculation...
I explain little more. The MAC address is valid only in Ethernet (Wifi) networks, which are local area networks (LANs). The global internet consists of many networks including LANs and other network types, in which there is no MAC at all. But internet works, because it uses IP-addresses, not MAC. According to network protocols hierarchy the lower-level protocols (Ethernet in our case) should not know what data they are transferring. The higher-level protocols (IP in our case) should not know by which lower-level protocols they are transferred. If this is not done, then a inspection of packets occurs. This is generally bad, because of many many things including security. More explanations you can find quickly in internet.
Originally Posted by Toengel
Now the question: if Philips have a MAC-address database of their TVs and can do any "reset" then this MAC-address is transferred from user TV to this database, right? How Philips can transfer the MAC not touching global network protocols hierarchy?
I can say even more. If i for example decide to disassembly my TV and to reprogram ethernet controller with another MAC then NetTV is for me no more accessible because of this "database"?
This all does not please me.